Izdelki za slepa prirobnica (8)
SAE Slepe Flanše in SAE Sendvič Plošče - STAUFF Flanše
SAE Blanking Flange and Counterflange BFX-CP / BAS-CP
▪ 3000 PSI Standard Pressure Series (based on ISO 6162-1:2006): 1/2" (DN13) ... 5" (DN127)
▪ 6000 PSI High Pressure Series (based on ISO 6162-2:2006): 1/2" (DN13) ... 2" (DN51)
▪ Material: S355J0 / C45 or equivalent, Stainless Steel 1.4404 on request (W5)
▪ Surface: blank, oiled
SAE Sandwich Plate - Female BSP Port SPL-G1/4-L
▪ e.g. for Test Couplings
▪ 3000 PSI Standard Pressure Series (based on ISO 6162-1:2006): 1/2" (DN13) ... 2" (DN51)
▪ 6000 PSI High Pressure Series (based on ISO 6162-2:2006): 1/2" (DN13) ... 2" (DN51)
▪ Materials: S355J0 / C45 or equivalent, Stainless Steel 1.4404 on request (W5)
▪ Surfaces: blank, oiled
SAE Blindplug CAG-BP
SAE Blindplug (High Version) CAG-BPH
▪ 3000 PSI Standard Pressure Series (acc. to ISO 6162-1:2006): 1/2" (DN13) ... 4" (DN102)
▪ 6000 PSI High Pressure Series (acc. to ISO 6162-2:2006): 1/2" (DN19) ... 2-1/2" (DN64)
▪ Materials: S355J0 / C45 or equivalent, Stainless Steel 1.4571...
FOLIJSKI FLANŠ
Eine weitere Anschlussart bietet der Folien-Flansch, welcher mit den verschiedensten Folientypen erhältlich ist.
MATERIAL
Erhältlich in folgenden Materialien:
PVC
EPDM
PIB
EVA
ECB
FPO
NENNWEITEN
DN 100, DN 125 und DN 160
iglidur® Brez vzdrževanja ležaj z obročem iglidur® ležaj z obročem
iglidur® flange bearing
d1 [mm]:
With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible.
When to use iglidur® flange bearings?
When you want a screw flanged bearing
When a clip bearing solution is not satisfactory as a sheet metal feedthrough
When there is a housing with very rough tolerances
When the tight fit of a press-fit bearing is not sufficient as an axial securing
When not to use them?
When an additional angle compensation is required
igubal® flange bearing
When a screw connection is not possible
iglidur® clip bearing
When a large guide length is necessary
iglidur® G
General features With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. The design enables high loads with minimum demand on the precision of the housing. iglidur® maintenance-free flange bearings are available in four materials - iglidur® G, iglidur® J, iglidur® X and iglidur® A180. Thus, with this design, a very wide range of applications - from the universal bearing through the highest wear resistance or temperature resistance (up to +250°C) up to FDA-compliant bearing solutions - can be covered.
Installation Dependent on the stressing capacities, various mounting types are used. For low radial loads, it is enough to mount the iglidur® flange bearing with just two screws on a surface. For higher radial loads, it is advisable to support the iglidur® flange bearing in a bore on the reinforced side in the load direction. Large tolerances are permitted for this bore, as it is only to additionally support the iglidur® flange bearing. In order to support still higher radial loads, the iglidur® flange bearing can be press-fitted with the longer side in an H tolerance bore. The additional screw connection secures the firm seating of the bearing in the housing. For the mounting of the iglidur® maintenance-free flange bearing, no special tools or devices are necessary. The alignment of the bearing in multiple mounted shafts is easily possible at the installation.
Available materials: iglidur® G, iglidur® A180, iglidur® J and iglidur® X
The mounting of the iglidur® flange bearing: Simple and safe
iglidur® flange bearing
d1 [mm]:
Notranji navoj
Wir schneiden, drücken bzw. rollieren Gewinde auf Wunsch in Stanzteile und Ziehteile.
Auch bei größeren Stückzahlen sind wir ein verlässlicher Partner und reagieren dabei schnell und innovativ auf Kundenwünsche. In unserem Betrieb werden auch anfallende Umfeldarbeiten an den zu bearbeitenden Teilen, wie z.B. Bohren, Taumelnieten, Montieren, Verpacken usw. ausgeführt.
